1、磁力研磨机用不锈钢针选择 Choice of grinding stainless pins
1）针愈粗研磨能力愈强，故选择针时以工件材质软硬为依据。不锈钢或铁类可选择直径0.5mm以上针，铜铝等其材质较软材料可选择直径0.5mm以下较适宜。当然磁力研磨机的磁力大小可无段调整，因此经测试多次后，即可选定适当的磨材。
The bigger the pins are, the better the grinding ability is. Thus, choose the pins should depend on the softness or hardness of the workpiece material. Can choose pins with diameter over 0.5mm for Stainless steel or Iron workpieces, and pins blow 0.5mm for softer material workpieces such as copper or aluminium.
Of cause the magnetic force of the machine is adjustable, thus can test for more times to get a suitable grinding pins.
2）要研磨工件的孔径大小，决定针的精细及长短，另如要研磨工件的孔内夹缝时，建议使用3mm长的针，效果较好。
The holes of the workpieces decide the big or ***all, long or short pins to be used. If the cracks into the holes are to be grinded, the 3mm long pin is suggested to be used for better effect.
3)不锈钢针磨材为***性材料，可连续使用。
The stainless steel pins are permanent grinding materials, can be used for many times.
2、研磨液功用 Function of Grinding Fluid
1)防锈、抛光、冷却、清洗、除油等功能。
Rust-prevent, polishing, cooling, cleaning and oil removing etc.
2)研磨液连续研磨约30分钟、温度可达70℃，请注意轮流交换。
The grinding fluid grinds for 30 minutes, its temperature can be 70℃, please change with cool one.
3)如工件表面含油太多，需先清洗除油再研磨。
If the surface of workpieces too oily, the oil should be removed first before grinding.
3、磁力研磨机注意事项 NOTES
1)电源必须有可靠接地
The power supply must h***e a reliable ground lead.
2)变频调试器功能键不可随意修改(以出厂时设置为准)
The function key of the frequency conversion adjuster should not be changed at will. (Factory setting is standard.)
3)研磨完成后，研磨工件必须在机器运转中拿走清洗(以免工件被磁化)
After grinding finishes, workpieces should be taken away during the machine running, so that the workpieces are not magnetized.
4)必须使用塑料质研磨桶，以免损坏工件
To ***oid damaging the workpieces, should use a PLASTIC container for grinding.
5)研磨槽内不可进水，以免损坏机器。
To ***oid damaging the machine, the grinding trough should not be watered.
4、磁力研磨机器*** Maintenance of Machines
1)每班清理研磨槽内掉下的钢针和水。
Clean the grinding trough per shift.
2)研磨槽内的胶垫每班使用前要清理钢针再使用。
Clean the rubber mat on the grinding trough before grinding.
3)研磨槽内排水管要保持畅通。
Keep unblocked to the drain pipe of the grinding trough.
4)机器表面要保持清洁、干爽。
Keep the surface of the machine clean and dry.
5)机器后面及底下风扇过滤网每30天要清理一次。
Clean the strainers to the fans on the back and bottom of the machine every 30 days.