聚乙烯压痕硬度测定仪
SLYQ-96A/3路
一、满足标准：
GB/T 23257-2009 埋地钢质管道聚乙烯防腐层
二、全自动聚乙烯压痕硬度测定仪概述：
本仪器主要测试聚乙烯在一定的温度环境和恒定的压力下经过一定的时间后的压痕深度。
本仪器是国内自动化程度***高，******的测试聚乙烯压痕硬度的测试仪器，由于做的时间比较长，试验人员只需要在试验前设定好参数后，会自动根据设置的实验条件进行加温，并保持恒温，能够自动加载，并自动采集结果、计算平均数值。实验完成后有报警提示，报警时间长短可以设定！
三、全自动聚乙烯压痕硬度测定仪产品特点：
1、本仪器核心控制部分通过7寸触摸屏设置参数并控制。
2、本仪器变形采集利用国内***的微型位移传感器技术，淘汰了利用数字千分表采集位移精度低、易坏及需要更换电池等缺陷
3、设置好参数后，点开始实验后自动加载，实验结束后自动计算结果，同时压头自动复位到初始位置进行下次实验
- 同时可以做三路实验，也可以单独进行一路或二路
- 本仪器带有微型打印机，可以对试验结果进行打印，并自动计算平均值。
- 测试环境温度为：室温-100度，温度可设定
- 具有报警提示，实验完成后根据设定的报警时间进行报警。
四、全自动聚乙烯压痕硬度测定仪技术参数：
1、试验负荷：10MP（25N）
2、压头直径：Ф1.8mm
3、控温精度：&plu***n;0.5度
4、压痕深度指示***小分度值：0.01mm
5、耐压时间：可以设定
6、主机变形量：≤0.04mm
7、测量范围有效值：可以设定
8、允许***大试样厚度：50MM
五、全自动聚乙烯压痕硬度测定仪主要配置及附件：
1、主 机： 一台
2、主机压头￠1.8mm：三个
3、微型打印机： 一台
4、自动加载装置： 三套
5、位移传感器： 三个
6、恒温加热装置： 一套
7、使用说明书： 一份
8、德国西门子PLC： 一个
9、德国西门子采集模块：一个
10、寸彩色触摸屏： 一个
英文资料简介如下：
Full automatic polyethylene indentation hardness tester
SLYQ-96A/3 Road
One, meet the standa***:
GB/T 23257-2009 polyethylene coating for buried steel pipeline
=====================================
Two, automatic determination instrument of polyethylene indentation hardness:
The instrument is mainly test of polyethylene in a definite temperature environment and the c***tant pressure after indentation depth after a certain time.
This instrument is the highest degree of automation, test instrument most leading testing polyethylene indentation hardness, as a result of the relatively long time, test personnel only need to set parameters in the test before and after, will automatically according to the experimental conditi*** set for heating, and keep c***tant temperature, capable of automatic loading, automatic acquisition and calculation results, the ***erage numerical. After completion of the experiment has alarm, alarm time can be set!
===============================
Three, automatic indentation hardness tester product features of polyethylene:
1, the instrument is the core control part through a 7 Inch Touch screen set up parameters and control.
2, the collection and utilization of micro displacement sensor deformation technology leading, eliminated using digital micrometer acquisition displacement precision is low, easily broken and the need to replace the battery and other defects
3, after parameter setting, some began to automatic loading experiment, automatic calculation results after the experiment, at the same time indenter automatic reset to the initial position for the next experiment
4, at the same time can do three experiments, can also be a road or two separate
5, the instrument with a micro printer, you can print the test results, and automatic calculation of ***erage value.
6, test environment temperature: room temperature -100 degrees, the temperature can be set
7, an alarming, after completion of the experiment according to the set alarm time and alarm.
==========================================
Tester technical parameters four, full automatic polyethylene indentation hardness:
1, the test load (25N): 10MP
2, the pressure head diameter: 1.8mm
3, temperature control precision is &plu***n; 0.5 degrees:
4, the indentation depth indicates the minimum scale value: 0.01mm
5, pressure time: you can set
6, the host deformation: ≤ 0.04mm
7, the effective value measurement range: can be set
8, to allow maximum thickness: 50MM
==============================
Five, automatic indentation hardness tester of polyethylene main configuration and accessories:
1, the main machine: a
2, the host head - 1.8mm: three
3, micro printer: a
4, automatic loading device: three sets
5, the displacement sensor: Three
6, a c***tant temperature heating device: a
7, the use of manual: a
8, Germany Siemens PLC: a
9, Germany Siemens acquisition module: a
10, inch color touch screen: a