目录
1 概述/SCOPE
2 输入特性/INPUT CHARACTERISTICS
3 输出特性/OUTPUT CHARACTERISTICS
4 保护功能/ PROTECTION FUNCTION
5环境要求/ENVIRONMENTAL REQUIREMENTS
6机械特性 MECHANICAL CHARACTERISTICS
7安全标准 /SAFETY
8.EMC 标准/ EMC STANDARD
9体积/VOLUME
10外观图/OUTLOOK DRAWING
11样品测试报告 / SAMPLES TEST REPORT
1 概述 /SCOPE
本规格书适合于HA01-050024XX型号的开关电源。
The purpose of the document is to the specify the functional requirements of HA01-050024XX switching power supply.
2．输入特性/ INPUT CHARACTERISTICS:
2.1 输入电压/ Input Voltage
额定输入电压/ Rated Input Voltage: 100-240Vac
可变输入电压/Variable input voltage : 90V—264Vac
2.2 输入电流/Input Current:
当输入额定电压 带额定负载时，最大的输入交流电流 0.35A
0.35A max when input rated voltage and output rated load.
2.3 输入频率/ Input Frequency
额定频率/Rate Frequency:50/60Hz
调整频率/ Variation Frequency: 47-63Hz
2.4 浪涌电流/In-rush Current:
当输出为额定负载，环境温度为25℃,输入240Vac冷启动时的最大浪涌电流为60A。
60 A mps Max Cold start at 240Vac input ,with rated load and 25℃ ambient.
2.5 AC漏电流/ AC leakage Current:
当输入电压240Vac 时， 最大的漏电流为0.25mA
0.25mA Max .At 240Vac input
3. 输出特性/OUTPUT CHARACTERISTICS:
3.1 额定输出功率/Rated Output Power 12W
3.2 负载特性/调整率（Combined Load/line Regulation）
电压 最小负载 最大负载 负载调整 空载输出电压
Voltage Min. Load Max Load Load Regulation Unload output voltage
+5V 0A 2.4A 4.9V-5.3V 4.75V-5.30V
3.3 效率/Efficiency:
V级平均工作效率≥74.74%
当输入115VAC 时，平均效率≥74.74%。是输出额定负载的25%,50%,75%,100%4种情况下平均效率，
115VAC input, the average efficiency ≥74.74%。 output rated load is 25%,50%,75%,100% 4 situations of average efficiency
当输入230VAC 时，平均效率≥74.74%。是输出额定负载的25%,50%,75%,100%4种情况下平均效率，
230VAC input, the average efficiency ≥74.74%。 output rated load is 25%,50%,75%,100% 4 situations of average efficiency
3.4 空载待机功率/Unload standby Power: 0.3W Max
3.5 纹波和噪音/ Ripple And Noise
纹波与噪声: 量测时示波器选用20MHz带宽限制,输出端要并联一颗0.1uF的陶瓷电容和一颗47uF的电解电容. (在额定输入及输出的条件下检测)
Ripple & Noise: Measurement is done by 20MHz bandwidth oscilloscope and the output paralleled a 0.1uF ceramic capacitor and a 47uF electrolysis capacitor. (test under the condition of rated input and rated output)
电压 电流 最大纹波最大噪音
Voltage current Ripple And Noise(Max)
+5V 2400mA 200m Vp-p
3.6 启动延迟时间/ Turn On Delay Time:
当输入100Vac 和输出最大负载时 ，最大启动时间为3S
3 second Max .At 100Vac input and output Max. Load
3.7 上升时间/ Rise Time:
当输入100Vac 和输出最大负载时最大时间为100ms
100ms Max. At 100Vac input and output Max. Load
3.8 保持时间/Hold Up Time :
当输入100Vac和输出最大负载时，最小保持时间为5ms
5ms 100Vac input and output Max .Load.
3.9 过充/ Overshoot:
在电源开启或关闭的时候,最大15%.
15% Max.When power supply at turn off/on.
4. 保护功能/ PROTECTION FUNCTION:
4.1 短路电路保护/Short circuit protection:
电源供给器在短路解除后能正常恢复工作。
The Power Supply will be auto recovered when short circuit faults remove.
4.2 过流保护/ Over current Protection:
4.3 过压保护/ Over Voltage Protection:
当输出电压超过额定电压的120%-150%时，电源将保护，故障排除后能恢复正常工作。
The power supply will auto recovered when the voltage over 120%-150% rate voltage.
5. 环境要求/ENVIRONMENTAL REQUIREMENTS
5.1 工作温度/Operating Temperature:
0℃-40℃,满载,正常工作.
0℃ to 40℃,Full load, Normal operation.
5.2 储藏温度/Storage Temperature:-20℃ to 80℃
带外壳/With package
5.3 工作湿度/Relative Humidity:
5%(0℃)~90%(40℃) ,72小时，满载，正常工作。
5%(0℃)~90%(40℃) 72h Full Load , Normal operating.
5.4 振动/ Vibration:
5.4.1测试标准：国际电工电子委员会
Operating: IEC 721-3-3 3M3
5~9Hz,A=1.5mm
加速度 （9～200Hz,Acceleration 5m/s）
5.4.2．运输 （Transportation）:
IEC 721-3-2 2M2
5~9Hz, A=3.5mm
9~200Hz ,加速度 Acceleration=5 m/s²
200~500Hz ,加速度 acceleration=15 m/s²
5.4.3. 轴向振动/ Axes,10 cycles per axis :
在测试过程中不能出现永久性的损坏.
No permanent damage may occur during testing.
在电源开启和关闭后,样机能够恢复到最初条件.
The SAMPLE has to restore to its original situation after power off/on..
6 . 机械特性/ MECHANICAL CHARACTERISTICS
6.1 跌落实验/ Dropping Testing ，
插墙式跌落高度为1米、桌面式跌落高度为760mm；
1M for wallmount type and 760mm for desktop type as above described;
测试台面是厚13mm的夹木板，离地面高19-20mm
The horizontal surface consists of hardwood at least 13mm thick, mounted on two layers of plywood
each 19mm to 20mm thick,all supported on a concrete or equivalent non-resilient floor.
6.2 摇摆实验/Cable Flexing Testing
DC引线吊重200克， 摇摆角60度，最少能承受2000次，弯曲速度每分40次，不会出现损伤。
The DC cord shall with weight of 200g,it swings at angle 60 deg ,2000cycle
Time min Bending speed: 40cycle per minute shall to be no breakage to the code
7. 安全标准SAFETY STANDARD ,
7.1 安全:符合标准 IEC60065，EN60065，UL60065，GB8898。
Safety Accord with IEC60065，EN60065，UL60065，GB8898。
注：相应的AC插脚对应相应国家的标准，如CE即对应为EN60065；3000Vac
Note: AC pins corresponding corresponding corresponding to national standards, such as the CE that corresponds to EN60065; 3000Vac。
7.2 高压/DIELECTRIC STRENGTH Hi-Pot:
初级对次级/Primary to secondary:4242Vdc/5mA/60S for type test.
7.3 绝缘阻抗/ Insulation resistance:
初级对次级/ Primary to secondary :10MΩ Min at 500V DC
8．EMI标准/EMI STANDARD
Meets the Limits of/测试符合.Fcc Part15 class B rules.
9．体积/VOLUME: L×W×H
长 68mm ×宽49.5mm×高28.2mm
10 外观图/OUTLOOK DRAWING（公差/Common difference：+/-0.2mm）