FEATURES:
l Up to 1.25Gb/s data links
l Hot-pluggable SFP footprint
l 1310nm Fabry-Perot laser tran***itter
l Duplex LC connector
l Compliant with SFP MSA and SFF-8472
l Digital Diagnostic Monitoring(DDM):Internal Calibration or External Calibration
l Very low jitter
l No Rate Select input required for
Fiber Channel 1x/2x Operation
l Up to 20km on 9/125μm ***F
l Metal enclosure, for lower EMI
l Single 3.3V power supply
l Low power dissipation <700mW typical
l CWDM is also ***ailable
l Class 1: FDA/IEC60825-1 Laser Security
APPLICATI***:
l Gigabit Ethernet
l 1x Fiber Channel
l Switch to Switch interface
l Switched backplane applicati***
l Router/Server interface
l Other optical tran***ission systems
Description:
BDTRP413L1SD-20 ***all Form Factor Pluggable (SFP) transceivers are compatible with the ***all Form Factor Pluggable Multi-Sourcing Agreement (MSA).They comply with laser safety standard IEC-60825 and Ethernet standard IEEE802.3z 1000Base-LX/LH and IEEE802.3ah.
The transceiver c***ists of two secti***: The tran***itter section incorporates a FP laser. the receiver section c***ists of a PIN photodiode integrated with a trans-impedance preamplifier (TIA).
All modules satisfy class I laser safety requirements. The optical output can be disabled by a TTL logic high-level input of Tx Disable. Tx Fault indicates that degradation of the laser. Loss of signal (LOS) output indicates the loss of an input optical signal of receiver. The SFP module can be compatible with other brand switch devices like Cisco,Huawei etc.The SFP module has the function of AGC (Automatic Gain control without attenuator).
Optical Characteristics (TOP = 0 to 70℃, VCC = 3.00 to 3.60 Volts)
|
Parameter |
Symbol |
Min |
Typ |
Max |
Unit |
Ref. |
|
Tran***itter |
||||||
|
Output Opt. Power |
POUT |
-9.5 |
|
-3 |
dBm |
1 |
|
Optical W***elength |
λ |
1270 |
1310 |
1355 |
nm |
2 |
|
Spectral Width |
σ |
|
|
3 |
nm |
2 |
|
Optical Modulation Amplitude |
OMA |
174 |
|
|
μW |
2,3 |
|
Optical Rise/Fall Time |
tr/ tf |
|
100 |
160 |
ps |
4 |
|
RIN |
|
|
|
-120 |
dB/Hz |
|
|
Deterministic Jitter Contribution |
TX Δ DJ |
|
20 |
56.5 |
ps |
5 |
|
Total Jitter Contribution |
TX Δ TJ |
|
70 |
119 |
ps |
|
|
Optical Extinction Ratio |
ER |
9 |
|
|
dB |
|
|
Receiver |
||||||
|
***erage Rx Sensitivity @ 1.25 Gb/s |
RSENS2 |
|
|
-22 |
dBm |
6, 7 |
|
(Gigabit Ethernet) |
|
|
|
|
|
|
|
***erage Received Power |
RxMAX |
|
|
0 |
dBm |
|
|
Receiver Elec. 3 dB cutoff freq. |
|
|
|
1500 |
MHz |
|
|
Optical Center W***elength |
λC |
1270 |
|
1600 |
nm |
|
|
Return Loss |
|
12 |
|
|
dB |
|
|
LOS De-Assert |
LOSD |
|
-23 |
-19 |
dBm |
|
|
LOS Assert |
LOSA |
-30 |
-25 |
|
dBm |
|
|
LOS Hysteresis |
|
0.5 |
|
|
dB |
|
Notes:
1. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulati***.
2. Also specified to meet curves in FC-PI 13.0 Figures 18 and 19, which allow trade-off between
w***elength, spectral width and OMA.
3. Equivalent extinction ratio specification for Fiber Channel. Allows ***aller ER at higher ***erage power.
4. Unfiltered, 20-80%. Complies with IEEE 802.3 (Gig. E), FC 1x and 2x eye masks when filtered.
5. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and D??DJ.
6. Measured with conformance signals defined in FC-PI 13.0 specificati***.
7. Measured with PRBS 27-1 at 10-12 BER