进口气动隔膜泵/Pneumatic diaphragm pump/德国品质
德国KAYSEN凯森进口气动隔膜泵概述
气动隔膜泵是目前业内***新颖的一种泵类。
气动隔膜泵采用压缩空气为动力源，对于各种腐蚀性液体，带颗粒的液体，高粘度、易挥发、***、***的液体，均能予以抽光吸尽。
泵体采用四种材质，铝合金、铸铁、工程塑料、不锈钢。根据不同液体介质分别采用丁晴橡胶、氯丁橡胶、氟橡胶、聚四氟乙烯。以满足不同用户的需要。
主要特点：
气动隔膜泵不需灌引水，吸程高达5m，产品扬程可以达到70米左右，出口压力≥7kgf/cm2; 流动宽敞，通过性能好，允许通过***大颗粒直径达10mm。抽送泥浆、杂质时，对泵磨损甚微; 扬程、流量可通过气阀开度实现无级调节（气压调节在1-7kgf/cm2之间）; 该气动隔膜泵无旋转部件，没有轴封，隔膜将抽送的介质与泵的运动部件、工作介质完全隔开，所输送的介质不会向外泄漏。所以抽送***、易发挥或腐蚀性介质时，不会造成环境污染和危害人身安全; 不必用电，在***、***场所使用安全可靠; 可以浸没在介质中工作;
使用方便、工作可靠、开停只需简单地打开和关闭气体阀门，即使由于意外情况而长时间无介质运行或突然停机，气动不锈钢隔膜泵也不会因此而损坏，不旦超负荷，泵会自动地停机，具有自我保护性能，当负荷***正常后，又有自动启动运行; 结构简单、易损件少，该气动不锈钢隔膜泵结构简单，安装、维修方便，泵输送的介质不会接触到配气阀，联杆等运动部件，不象其他类型的泵因转子、活塞、齿轮、叶片等部件的磨损而使性能逐步下降; 可输送较粘的液体（粘度在1万厘泊以下）; 本泵无须用油润滑，即使空转，对气动不锈钢隔膜泵也无任何影响。
（1）泵不会过热：压缩空气作动力，在排气时是一个膨胀吸热的过程，气动泵工作时温度是降低的，无***气体排出。
（2）不会产生电火花：气动隔膜泵不用电力作动力，接地后又防止了静电火花。
（3）可以通过含颗粒液体：因为容积式工作且进口为球阀，所以不容易被堵。
（4）对物料的剪切力极低：工作时是怎么吸进怎么吐出，所以对物料的搅动***小，适用于不稳定物质的输送。
（5）流量可调节，可以在物料出口处加装节流阀来调节流量。
（6）具有自吸的功能。
（7）可以空运行，而不会有***。
（8）可以潜水工作。
（9）可以输送的流体极为广泛，从低粘度的到高粘度的，从腐蚀性的到粘稠的。
（10）没有复杂的控制系统，没有电缆、***丝等。
（11）体积小、重量轻，便于移动。
（12）无需润滑所以维修简便，不会由于滴漏污染工作环境。
（13）泵始终能保持***，不会因为磨损而降低。
（14）***的能量利用，当关闭出口，泵自动停机，不存在设备移动、磨损、过载、发热。
（15）没有动密封，维修简便避免了泄漏，工作时无死点。
主要优点：
●使用方便、工作可靠、开停只需简单地打开和关闭气体阀门，即使由于意外情况而长时间无介质运行或突然停机泵也不会因此而损坏，一旦超负荷，泵会自动地停机，具有自我保护性能，当负荷***正常后，又能自动启动运行
●结构简单、易损件少，该泵结构简单，安装、维修方便，泵输送的介质不会接触到配气阀，联杆等运动部件，不像其他类型的泵因转子、活塞、齿轮、叶片等部件的磨损而使性能逐步下降
●可输送较粘的液体(粘度在1万厘泊以下）
●不需灌引水，吸程高达5米，扬程达70米，出口压力≧7bar
●流动宽敞，通过性能好，允许通过***大颗粒直径达10毫米。抽送泥浆、杂质时，对泵磨损甚微
●本泵无须用油润滑，即使空转，对泵也无任何影响
●不必用电，在***、***场所使用安全可靠
●可以浸没在介质中工作
●扬程、流量可通过气阀开度实现无级调节(气压调节在1-7bar之间)
●该泵无旋转部件，没有轴封，隔膜等抽送的介质与泵的运动部件、工件介质完全隔开，所输送的介质不会向外泄漏。所以抽送***、易挥发或腐蚀性介质时，不会造成环境污染和危害人身安全
主要应用：
●油井钻好后，用气动隔膜泵吸沉积物及灌浆。
●吸各种乳剂和填料。
●吸各种污水。
●各种强酸、强碱、强腐蚀液体。
●吸各种高温液体***高可耐150度。
●可以吸花生酱、泡菜、土豆泥、小红肠、果酱苹果浆、巧克力等。
●矿井、坑道、隧道、选矿、矿渣中的积水。泵吸水泥灌浆及灰浆。
●不锈钢隔膜泵泵吸各种橡胶浆。
●不锈钢气动隔膜泵可以吸各种磨料、腐蚀剂、石油及泥浆、清洗油垢及一般容器。
●可以吸各种***、***、易挥发液体。
●不锈钢气动隔膜泵可以用于吸油漆、树胶、颜料。
●不锈钢气动隔膜泵作为各种固液体分离设备的前级送压装置。
●气动隔膜泵可以用于为油轮，驳船清仓吸取仓内污水。
●吸啤酒花及发酵粉稀浆、糖浆、糖密。
●粘合剂和胶水、全部种类可用泵吸取。
●各种瓦、瓷、砖器及陶器釉浆。
Germany KAYSEN imported pneumatic diaphragm pump overview
The pneumatic diaphragm pump is currently the most innovative type of pump in the industry.
The pneumatic diaphragm pump uses compressed air as the power source. For various corrosive liquids, liquid with particles, high viscosity, volatile, flammable, highly toxic liquid, can be exhausted.
The pump body is made of four materials, aluminum alloy, cast iron, engineering plastics and stainless steel. NBR, neoprene, fluororubber, and polytetrafluoroethylene are used according to different liquid media. To meet the needs of different users.
main feature:
The pneumatic diaphragm pump does not need to be irrigated, the suction stroke is up to 5m, the product lift can reach 70 meters, the outlet pressure is ≥7kgf/cm2; the flow is spacious, the pass performance is good, and the maximum particle diameter is allowed to reach 10mm. When the mud and impurities are pumped, the pump wears little; the lift and flow can be adjusted steplessly by the valve opening (the air pressure is adjusted between 1-7kgf/cm2); the pneumatic diaphragm pump has no rotating parts and no shaft seal. The diaphragm completely separates the pumped medium from the moving parts of the pump and the working medium, and the delivered medium does not leak outward. Therefore, when pumping toxic, easy to play or corrosive media, it will not cause environmental pollution and harm to personal safety; it does not need electricity, it is safe and reliable to use in flammable and explosive places; it can be submerged in the medium;
Easy to use, reliable in operation, easy to open and close, only need to open and close the gas valve, even if there is no medium running or sudden stop due to unexpected circumstances, the pneumatic stainless steel diaphragm pump will not be damaged, and the pump will not be overloaded. Automatic shutdown, self-protection performance, when the load returns to normal, there is automatic start-up operation; simple structure, less wearing parts, the pneumatic stainless steel diaphragm pump is simple in structure, easy to install and maintain, the medium transported by the pump will not be exposed Valves, linkages and other moving parts, unlike other types of pumps, the performance of the rotor, pist***, gears, blades and other components wear down gradually; can transport a more viscous liquid (viscosity below 10,000 centipoise); The pump does not need to be lubricated with oil, even if it is idling, it has no effect on the pneumatic stainless steel diaphragm pump.
(1) The pump will not overheat: the compressed air is used as the power, and it is a process of expansion and heat absorption when exhausting. The temperature of the pneumatic pump is reduced when working, and no harmful gas is discharged.
(2) No spark is generated: the pneumatic diaphragm pump does not use electric power for power, and prevents static sparks after grounding.
(3) It can pass through the liquid containing particles: because it is volumetric and the inlet is a ball valve, it is not easy to be blocked.
(4) The shearing force on the material is extremely low: how to suck in when working, so the agitation of the material is minimal, and it is suitable for the transportation of unstable substances.
(5) The flow rate can be adjusted, and a throttle valve can be added at the material outlet to adjust the flow rate.
(6) It has the function of self-priming.
(7) It can be run empty without danger.
(8) You can work diving.
(9) The fluids that can be transported are extremely wide, from low viscosity to high viscosity, from corrosive to viscous.
(10) There is no complicated control system, no cables, fuses, etc.
(11) ***all size, light weight and easy to move.
(12) It is easy to maintain without lubrication, and it will not pollute the working environment due to dripping.
(13) The pump is always efficient and will not be degraded by wear.
(14) 100% energy utilization, when the outlet is closed, the pump automatically stops, there is no equipment movement, wear, overload, heat.
(15) There is no dynamic seal, the maintenance is simple and ***oids leakage, and there is no dead point during work.
The main advantage:
●Easy to use, reliable in operation, easy to open and close the gas valve, even if there is no medium running or sudden shutdown due to unexpected conditi***, the pump will not be damaged. Once overloaded, the pump will automatically stop. Self-protection, when the load returns to normal, it can automatically start running
●The structure is simple and the wearing parts are few. The pump has a simple structure, convenient installation and maintenance. The medium conveyed by the pump will not touch the moving parts such as the valve, the connecting rod, etc., unlike other types of pumps due to the rotor, piston, gear, Wear of parts such as blades and the performance is gradually reduced
●It can transport relatively sticky liquid (viscosity below 10,000 centipoise)
● No need to irrigate water, suction up to 5 meters, lift up to 70 meters, outlet pressure ≧ 7bar
●The flow is spacious and the pass performance is good, allowing the maximum particle diameter to reach 10 mm. When pumping mud and impurities, the pump wears little
●The pump does not need to be lubricated with oil, even if it is idling, it has no effect on the pump.
●No need to use electricity, safe and reliable in flammable and explosive places
● can be submerged in the medium to work
●The head and flow can be adjusted steplessly by the opening of the valve (the air pressure is adjusted between 1-7bar)
●The pump has no rotating parts, no shaft seal, and the medium pumped by the diaphragm is completely separated from the moving parts of the pump and the workpiece medium, and the medium to be transported will not leak outward. Therefore, when pumping toxic, volatile or corrosive media, it will not cause environmental pollution and endanger personal safety.
main application:
● After drilling the oil well, pump the sediment and grout with a pneumatic diaphragm.
● Aspirate various emulsi*** and fillers.
● Suction all kinds of sewage.
● A variety of strong acids, strong alkalis, strong corrosive liquids.
●It can withstand up to 150 degrees of high temperature liquid.
● Can absorb peanut butter, kimchi, mashed potatoes, ***all red sausage, jam apple pulp, chocolate, etc.
● Water in mines, tunnels, tunnels, beneficiation, and slag. Pumping cement grout and mortar.
●Stainless steel diaphragm pump pumps all kinds of rubber slurry.
●Stainless steel pneumatic diaphragm pump can absorb all kinds of abrasives, corrosives, oil and mud, cleaning grease and general containers.
● Can absorb a variety of highly toxic, flammable, volatile liquids.
●Stainless steel pneumatic diaphragm pump can be used to absorb paint, gum and pigment.
●Stainless steel pneumatic diaphragm pump is used as the front stage pressure supply device for various solid liquid separation equipment.
●Pneumatic diaphragm pump can be used to pick up the sewage in the tank for the tanker and barge clearance.
●Suck hops and fermented powder slurry, syrup and sugar.
●Adhesives and glues, all types can be pumped.
●All kinds of tiles, porcelain, bricks and pottery glaze.