进口热水潜水泵/Submersible pump/德国品质
德国KAYSEN凯森进口热水潜水泵概述
进口热水潜水泵主要适用于抽取地下热水用来冬季供暖，洗浴，给工业企业提供能源，也可作为工业热水循环泵之用，由于安装方便，无需基础***，被广大用户所接受。
主要特点：
●可以抽取150℃以内的高温热水。
●用户需要时可以选用卧式潜水泵。
●安装方便，放到水池里通上电源就可使用。
●不容易进空气，所以不存在灌泵的麻烦。
●电机采用耐高温防水线，水润滑、水冷却、不易对环境造成污染。
●不需要建设泵房节约基建***。
●设备运行性能稳定噪音***。
主要应用：
适用于地热、温泉、冶金、化工、纺织、木材加工、造纸以及饭店、浴室、宾馆等锅炉高温热水增压循环输送以及城市住房采暖循环用泵，使用温度150℃以下。
热水潜水泵的***：
●定期查看易损件
首先查看潜水泵，潜水电泵，清水泵叶轮、扣环、轴套、轴承座等易损件是否无缺。好的可继续运用，坏的则有必要在替换新的合格零件之后重新装配运用，禁止运用损害和不合格的零件。
●替换光滑油
分别翻开密封室和电动机内部的油孔螺钉，把密封室内和电动机内部的光滑油悉数放出，替换新油，以保证光滑系统的正常作业。
●保证潜水泵，潜水电泵，清水泵密封
在替换密封室内的光滑油时，假如发现油质污浊且含水量已超支，则有必要替换整体密封盒或者动、静密封环，替换的零件有必要为合格产品，以保证其密封功能。
●驱除湿润水分
对绝缘电阻值低于0.5兆欧的电动机绕组，有必要驱除湿润水分，干燥的办法同一般的电动机相同。若密封盒不需替换时，能够只将电泵的定子部分拆下，一般情况下，密封盒部分应尽量不拆装，如的确需求拆装，则“O”形橡胶封环有必要替换新的。
●查看潜水泵，潜水电泵，清水泵轴承
查看电动机部分的上、下轴承，若发现磨损或空隙过大，有必要及时替换新的轴承，禁止将就运用，以免造成更大的经济损失。
●拆泵壳防生锈
春季运用之前，应拆开***上一级泵壳，滚动叶轮后再合闸发动，以防部件锈死不能正常发动而烧毁电动机绕组，这项***对充水式电动机尤为重要。
●保证轴承光滑
对充水式潜水泵应查看替换上下端盖轴承室的骨架油封及锂基光滑脂，以保证轴承长时间在光滑杰出的状态下正常运行。
Germany KAYSEN imported hot water submersible pump overview
The imported hot water submersible pump is mainly suitable for extracting underground hot water for heating in winter, bathing, providing energy for industrial enterprises, and also can be used as industrial hot water circulation pump. Due to convenient installation, no basic investment is required, and it is accepted by the majority of users.
main feature:
●It can extract high temperature hot water within 150 °C.
●The horizontal submersible pump can be used when the user needs it.
●Easy to install, put it in the sink and use it.
● It is not easy to enter the air, so there is no trouble in pumping.
●The motor adopts high temperature resistant waterproof wire, water lubrication, water cooling, and is not easy to pollute the environment.
● There is no need to build a pump house to s***e infrastructure investment.
● The running performance of the equipment is stable and the noise is extremely ***all.
main application:
It is suitable for geothermal, hot spring, metallurgy, chemical, textile, wood processing, papermaking, high temperature hot water pressurized circulation transportation of boilers, hotels, bathrooms, hotels, etc., as well as urban housing heating cycle pumps, using temperatures below 150 °C.
Maintenance of hot water submersible pumps:
● Regularly view c***umables
First check the submersible pump, submersible pump, clean pump impeller, retaining ring, bushing, bearing housing and other wearing parts are not missing. Good can continue to be used, and bad ones need to be reassembled after replacing new qualified parts, and it is forbidden to use damaged and unqualified parts.
● Replace ***ooth oil
Open the oil hole screw inside the sealing chamber and the motor separately, and release the ***ooth oil in the sealed chamber and the motor inside to replace the new oil to ensure the normal operation of the ***ooth system.
● Guarantee submersible pump, submersible pump, clean water pump seal
When replacing the ***ooth oil in the sealed chamber, if the oil is found to be dirty and the water content has been exceeded, it is necessary to replace the integral sealing box or the dynamic and static sealing ring. The replacement parts need to be qualified products to ensure the sealing function.
●Removing moist moisture
For motor windings with insulation resistance values below 0.5 megohms, it is necessary to remove wet moisture. The drying method is the same as that of a normal motor. If the sealed box does not need to be replaced, it can only remove the stator part of the electric pump. Under normal circumstances, the sealed box part should be disassembled as much as possible. If it is really necessary to disassemble, it is necessary to replace the new "O" rubber seal ring. of.
●View submersible pump, submersible pump, clear water pump bearing
Look at the upper and lower bearings of the motor part. If it is found that the wear or the gap is too large, it is necessary to replace the new bearing in time, and it is forbidden to use it, so as to ***oid further economic loss.
●Removal of the pump casing against rust
Before the spring application, the uppermost pump casing should be di***antled, and the impeller should be rolled and then closed to prevent the components from rusting and unable to start normally and burn the motor windings. This maintenance is especially important for water-filled motors.
● Ensure that the bearing is ***ooth
For the water-filled submersible pump, the skeleton oil seal and the lithium-based ***ooth grease of the upper and lower end cap bearing chambers should be replaced to ensure the normal operation of the bearing in a ***ooth and outstanding state for a long time.